Introduction: Matching a JX4D24 assembly to a light truck starts with the part number, nameplate, VIN, cooling layout, and emissions hardware.
Those details establish whether the assembly can enter the replacement or conversion plan. When a light truck arrives with a seized or badly worn engine, or a conversion workshop plans a repower, the first question is whether the JX4D24 2.4L assembly will fit. The answer depends on the numbers stamped on the vehicle and on the engine being replaced. Work in this order: confirm part number and vehicle identity, check cooling and emissions layout, then describe how the truck is used. That sequence keeps the inquiry specific and gives a supplier the details needed to assess the match.
The assembly carries P/N 0101001 / JX4D24, a 2.4L water-cooled turbocharged four-cylinder diesel. This number establishes the displacement family, cylinder count, and general architecture. Vehicle identity then narrows the match: nameplate model, VIN, model year, and OEM number stamped on the engine currently fitted. JX4D24 output runs from 90 to 110 kW and 360 to 420 N·m depending on variant, so two units that look similar externally can carry different calibration, injector hardware, and accessory brackets. For that reason, diesel engine builders ask for the OEM number before quoting; it is far cheaper than finding a variant difference after delivery. Vehicle identity matters most on localized models. The JX4D24 appears in JMC Kaiyun, Shunda, and Kairui light trucks, selected Yuhu 7 and Yuhu 9 pickups, Teshun vans, and selected localized Ford Transit diesel versions. These references identify the right engine family, which helps when a customer describes a vehicle in familiar terms. They still require confirmation that the chassis uses the same engine harness, accessory drive, and aftertreatment arrangement. A nameplate photo, VIN, and engine number give a shop a precise answer; a model name alone may lead to a shortlist and a request for more detail.
Once part number and vehicle identity align, physical layout determines whether the assembly fits the available space. On a light truck, two areas drive the difference: charge-air cooling and exhaust aftertreatment. Both add hardware around the block and both compete for space under the cab and along the frame rail.
The JX4D24 is offered in intercooled and non-intercooled variants, and the difference affects installation planning. An intercooler sits between the turbocharger and the intake, so it requires a core, pipe runs, and mounting points in front of the radiator pack. Turbocharging compresses intake air and raises its temperature; cooling that charge increases air density and helps keep combustion temperatures in a controlled range. During a conversion, settle the front-end layout before ordering the engine. Diesel engine manufacturers offer both layouts because chassis differ. If the donor truck never had a charge-air cooler, the intercooled assembly can still be included in the plan, but the pipe route and core space become part of the conversion.
The JX4D24 is a National VI b engine built around EGR plus DOC, DPF, and SCR, and that hardware is part of the assembly. The DOC oxidizes hydrocarbons and carbon monoxide, the DPF traps soot and regenerates on a cycle, and the SCR uses urea injection to reduce NOx. The three components work as one thermal system, so their order and spacing along the exhaust path matter as much as canister volume. On a light truck, check space for the dosing module, urea tank, upstream and downstream sensors, and a canister long enough for the system. Measure the frame rail, tank location, and clearance near the rear axle before finalizing the plan.
Two workshops can order identical part numbers and get different results because their trucks do different work. A 2.4L four-cylinder in a city delivery truck that idles in traffic for six hours a day sees a very different thermal and duty cycle from the same engine pulling a loaded pickup up a mountain grade. Truck engine manufacturers rate power and torque at defined test conditions, while the real route determines whether the 90 kW or 110 kW end of the JX4D24 range suits the job. For a vehicle that spends its life at gross weight on long grades, the higher-output calibration and intercooled layout make sense. For short urban runs with light loads, the lower end of the range is often the more sensible match. Climate and service access belong in the same conversation. Ambient heat, dust, and stop-and-go traffic increase the load on the cooling system and on DPF regeneration. A truck that rarely gets a long highway run has fewer natural opportunities to burn off accumulated soot, so the aftertreatment strategy matters as much as the engine itself. Fuel quality and urea supply in the operating region affect how well any National VI b system performs over the years. Write these conditions into the inquiry: daily route, typical payload, ambient temperature range, and fuel sulfur level. That detail supports a specific recommendation and a workable replacement plan.
Matching a 4 cylinder diesel engine assembly to a light truck follows a sequence. Start with P/N 0101001 / JX4D24 and confirm it against the nameplate, VIN, and OEM number on the engine being replaced. Then settle intercooled versus non-intercooled, check that the EGR, DOC, DPF, and SCR hardware will physically fit on the chassis, and describe how the truck actually works. These four steps make a supplier conversation short and specific. Our team at Truck Parts OEM Manufacturer can review a nameplate photo, VIN, OEM number, cooling layout, emissions configuration, and use conditions, then map the assembly against them and return configuration options, quantity pricing, and shipping arrangements.
A: Read the OEM number off the engine in the truck and compare it with P/N 0101001 / JX4D24 on the replacement assembly. Then confirm the nameplate model, VIN, and model year against the listed references for that engine family. The part number fixes the engine family and variant; the vehicle details confirm the cooling layout, harness, and aftertreatment arrangement the chassis was built for. Submit both together.
A: Yes. The intercooled version adds a charge-air cooler core, pipe runs, and mounting points in front of the radiator pack, so the front-end layout has to be planned before ordering. The non-intercooled version keeps that space free. Both are water-cooled turbocharged 2.4L four-cylinders with the same displacement family, but the plumbing differs, and the chassis needs room for the chosen layout.
A: Send the OEM number from the current engine, the nameplate photo, the VIN, the model year, and the transmission mated to it. Add cooling layout (intercooled or not), the emissions configuration currently on the truck, and the duty cycle — daily route, payload, and climate. Those details let a supplier assess whether the JX4D24 assembly matches your chassis and which output variant fits the work.
Diesel engine - Energy Education
China: Light-duty: Emissions | Transport Policy